NovaCraft™ — Achieve Clean-Cut Mortises & Slots Without Router Drift
Quit Wrestling a Wandering Router — Make Mortises & Slots That Hit Your Marks Every Time
Freehand routing is where good builds go sideways. The NovaCraft™ Router Mortise & Slot Jig secures your trim router between two aluminum guide rails, locks the bit on an exact parallel path, and lets you create precise mortises, grooves, and hidden-fastener slots right along any board’s edge — no wobble, no tear-out, no do-overs.
Crooked Mortises Aren't a Talent Issue — They’re a Setup Flaw
You marked and measured. You started cutting sharp. Then two inches in, the router dragged, the bit veered, and you ended up with a sloppy mortise on a piece you can’t swap out. Compact trim routers lack a true edge guide, and most aftermarket clamps are clunky plastic that slides the moment you push.
➤ Twin Aluminum Rails Secure the Cut Line: Two anodized aluminum rails clamp firmly to both sides of your stock, so the router rides perfectly parallel from start to finish — no drift, no sliding across the grain.
➤ Four Thumbscrews Fine-Tune Slot Placement: Hand-tighten knurled thumbscrews to precisely adjust the bit’s edge distance. Centered mortises, offset grooves, or fastener slots — all from one jig, no shims or calculations needed.
➤ Transparent Acrylic Base for Exact Layout: Watch your pencil marks, bit, and stops through a 1/4-inch acrylic plate. Plunge exactly where you planned — every single time.
Clamps to Any 65mm Trim Router — No Drilling, No Mods Needed
If your trim router barrel is between 63.5mm and 65mm — fitting most Makita, DeWalt, Bosch, Milwaukee, and Ryobi palm and trim routers — NovaCraft™ slips on, locks tight, and has you cutting in under two minutes. The included 1/4-inch shank straight bit (11mm diameter, 30mm cutting length) is ready for hinge mortises, biscuit slots, and 8mm/10mm hidden-fastener grooves right out of the box.
Other guides flex when you press against them. NovaCraft™’s aluminum rails sit flush, hold a vise-like grip on your workpiece, and let you lean into the router without the jig drifting from the edge.
Why Both Hobbyists & Pros Are Ditching Old Edge Guides for NovaCraft™
Woodworkers who’d given up on freehand mortising — the ones pulling out chisels for every hinge — are setting up NovaCraft™ once and cranking out joinery usually charged out by cabinet shops. As one user said: "Wish I’d had this before the kitchen job. Cut six bad mortises down to zero."
Cuts You Used to Avoid — Now You Finish Them in Minutes
✓ Consistent Hinge Mortises: Set the rails once, cut every door identically. No swapping templates, no double-measuring.
✓ Perfect Concealed-Fastener Slots: Cut clean Z-clip and panel-connector grooves for flat-pack furniture and edge-joined panels — joinery that used to need a $400 specialty jig.
✓ Professional-Looking Edges: Sturdy anodized aluminum rails won’t flex, knurled steel thumbscrews stay tight under vibration, and the acrylic base resists knocks and resin.
How to Use NovaCraft™: Three Steps, Ready for Your First Cut in Under Two Minutes
Step 1: Set your trim router into the clear acrylic collar and hand-tighten the side clamp until the barrel is firm.
Step 2: Press the twin aluminum rails against both sides of your stock and lock the four thumbscrews — the bit is now locked on a fixed path.
Step 3: Power on, plunge to depth, and guide the router between stop marks. Lift and you’ve got a perfect mortise at the first try.
| NovaCraft™ Mortise & Slot Jig | Freehand / Chisel | Generic Plastic Edge Guides |
|---|---|---|
| Tracks perfectly parallel on edge with twin aluminum rails | ❌ Wanders, depends on steady hands | ❌ Single rail, distorts under pressure |
| Cuts mortises & concealed-fastener slots from one setup | ❌ Separate tool for each cut | ❌ Mortising only, no slots for fasteners |
| Fits 63.5–65mm trim routers — Makita, DeWalt, Bosch, Milwaukee | ❌ N/A | ❌ Often router-specific, brand-locked |
Specifications – The Essentials You Need to Know
- Type: Dual-Purpose Router Mortise & Slot Jig
- Functions: Edge Mortising / Slotting + Hidden-Fastener Slot Cutting
- Router Fit: 63.5–65mm (2.5"–2.56") barrel diameter — suits most compact / trim / palm routers
- Base Size: 165mm × 104mm × 36mm (6.5" × 4.09" × 1.42")
- Included Bit: 1/4" (6.35mm) shank straight bit — 11mm cutting diameter, 30mm cut length, 60mm total length
- Construction: Anodized aluminum rails, clear acrylic collar, knurled steel thumbscrews
Your Questions, Answered
Will it work with my router?
If your trim or palm router barrel measures between 63.5mm and 65mm — fitting Makita RT0700/RT0701, DeWalt DCW600/DWP611, Bosch Colt PR20EVS, Milwaukee 2723-20, and most Ryobi palm routers — it fits perfectly. Be sure to measure your router barrel if unsure before ordering.
What types of cuts can I do with it?
Hinge mortises, biscuit or domino-style slots, edge dados for shelf supports, channels for sliding hardware, and slots for invisible Z-clip fasteners on flat-pack panels. The included 11mm bit suits common slot sizes; swap to other 1/4" shank straight bits for varied widths.
Is it sturdy enough for hardwood or just softwoods?
The aluminum rails and steel thumbscrews comfortably handle oak, walnut, maple, and hardwood plywood without bending. For dense hardwoods, take two passes to keep the bit sharp and cuts clean.
How fast is the first setup?
Insert the router, clamp the rails to the stock, adjust the thumbscrews, plunge to depth — under two minutes from unboxing to first mortise after you’ve done it twice.
Crafted Like the Jig You’d Build Yourself — If You Had a CNC and a Free Day
If NovaCraft™ doesn’t deliver cleaner, more accurate mortises than your current method on the very first project, send it back for a full refund. No restocking fees, no proof required — your workshop, your decision.
Original: $19.99
-70%$19.99
$6.00Product Information
Product Information
Shipping & Returns
Shipping & Returns
Description
Quit Wrestling a Wandering Router — Make Mortises & Slots That Hit Your Marks Every Time
Freehand routing is where good builds go sideways. The NovaCraft™ Router Mortise & Slot Jig secures your trim router between two aluminum guide rails, locks the bit on an exact parallel path, and lets you create precise mortises, grooves, and hidden-fastener slots right along any board’s edge — no wobble, no tear-out, no do-overs.
Crooked Mortises Aren't a Talent Issue — They’re a Setup Flaw
You marked and measured. You started cutting sharp. Then two inches in, the router dragged, the bit veered, and you ended up with a sloppy mortise on a piece you can’t swap out. Compact trim routers lack a true edge guide, and most aftermarket clamps are clunky plastic that slides the moment you push.
➤ Twin Aluminum Rails Secure the Cut Line: Two anodized aluminum rails clamp firmly to both sides of your stock, so the router rides perfectly parallel from start to finish — no drift, no sliding across the grain.
➤ Four Thumbscrews Fine-Tune Slot Placement: Hand-tighten knurled thumbscrews to precisely adjust the bit’s edge distance. Centered mortises, offset grooves, or fastener slots — all from one jig, no shims or calculations needed.
➤ Transparent Acrylic Base for Exact Layout: Watch your pencil marks, bit, and stops through a 1/4-inch acrylic plate. Plunge exactly where you planned — every single time.
Clamps to Any 65mm Trim Router — No Drilling, No Mods Needed
If your trim router barrel is between 63.5mm and 65mm — fitting most Makita, DeWalt, Bosch, Milwaukee, and Ryobi palm and trim routers — NovaCraft™ slips on, locks tight, and has you cutting in under two minutes. The included 1/4-inch shank straight bit (11mm diameter, 30mm cutting length) is ready for hinge mortises, biscuit slots, and 8mm/10mm hidden-fastener grooves right out of the box.
Other guides flex when you press against them. NovaCraft™’s aluminum rails sit flush, hold a vise-like grip on your workpiece, and let you lean into the router without the jig drifting from the edge.
Why Both Hobbyists & Pros Are Ditching Old Edge Guides for NovaCraft™
Woodworkers who’d given up on freehand mortising — the ones pulling out chisels for every hinge — are setting up NovaCraft™ once and cranking out joinery usually charged out by cabinet shops. As one user said: "Wish I’d had this before the kitchen job. Cut six bad mortises down to zero."
Cuts You Used to Avoid — Now You Finish Them in Minutes
✓ Consistent Hinge Mortises: Set the rails once, cut every door identically. No swapping templates, no double-measuring.
✓ Perfect Concealed-Fastener Slots: Cut clean Z-clip and panel-connector grooves for flat-pack furniture and edge-joined panels — joinery that used to need a $400 specialty jig.
✓ Professional-Looking Edges: Sturdy anodized aluminum rails won’t flex, knurled steel thumbscrews stay tight under vibration, and the acrylic base resists knocks and resin.
How to Use NovaCraft™: Three Steps, Ready for Your First Cut in Under Two Minutes
Step 1: Set your trim router into the clear acrylic collar and hand-tighten the side clamp until the barrel is firm.
Step 2: Press the twin aluminum rails against both sides of your stock and lock the four thumbscrews — the bit is now locked on a fixed path.
Step 3: Power on, plunge to depth, and guide the router between stop marks. Lift and you’ve got a perfect mortise at the first try.
| NovaCraft™ Mortise & Slot Jig | Freehand / Chisel | Generic Plastic Edge Guides |
|---|---|---|
| Tracks perfectly parallel on edge with twin aluminum rails | ❌ Wanders, depends on steady hands | ❌ Single rail, distorts under pressure |
| Cuts mortises & concealed-fastener slots from one setup | ❌ Separate tool for each cut | ❌ Mortising only, no slots for fasteners |
| Fits 63.5–65mm trim routers — Makita, DeWalt, Bosch, Milwaukee | ❌ N/A | ❌ Often router-specific, brand-locked |
Specifications – The Essentials You Need to Know
- Type: Dual-Purpose Router Mortise & Slot Jig
- Functions: Edge Mortising / Slotting + Hidden-Fastener Slot Cutting
- Router Fit: 63.5–65mm (2.5"–2.56") barrel diameter — suits most compact / trim / palm routers
- Base Size: 165mm × 104mm × 36mm (6.5" × 4.09" × 1.42")
- Included Bit: 1/4" (6.35mm) shank straight bit — 11mm cutting diameter, 30mm cut length, 60mm total length
- Construction: Anodized aluminum rails, clear acrylic collar, knurled steel thumbscrews
Your Questions, Answered
Will it work with my router?
If your trim or palm router barrel measures between 63.5mm and 65mm — fitting Makita RT0700/RT0701, DeWalt DCW600/DWP611, Bosch Colt PR20EVS, Milwaukee 2723-20, and most Ryobi palm routers — it fits perfectly. Be sure to measure your router barrel if unsure before ordering.
What types of cuts can I do with it?
Hinge mortises, biscuit or domino-style slots, edge dados for shelf supports, channels for sliding hardware, and slots for invisible Z-clip fasteners on flat-pack panels. The included 11mm bit suits common slot sizes; swap to other 1/4" shank straight bits for varied widths.
Is it sturdy enough for hardwood or just softwoods?
The aluminum rails and steel thumbscrews comfortably handle oak, walnut, maple, and hardwood plywood without bending. For dense hardwoods, take two passes to keep the bit sharp and cuts clean.
How fast is the first setup?
Insert the router, clamp the rails to the stock, adjust the thumbscrews, plunge to depth — under two minutes from unboxing to first mortise after you’ve done it twice.
Crafted Like the Jig You’d Build Yourself — If You Had a CNC and a Free Day
If NovaCraft™ doesn’t deliver cleaner, more accurate mortises than your current method on the very first project, send it back for a full refund. No restocking fees, no proof required — your workshop, your decision.
